MYMM® Store CA

A registered trademark from the Canada

Category

Category

Sale!

Imachinist S64514 Bi-metal Band Saw Blades 64-1/2″ X 1/2″ X 14tpi for Cutting Metal

Original price was: $46.74.Current price is: $38.95.

  • Bi-metal type, 64-1/2″ long, 1/2″ wide, 14tpi
  • 14tpi is suitable for cutting thin pipe tube profiles etc
  • 14TPI is fixed teeth profile, teeth distance is 1.8mm per teeth
  • Perfect for soft ferrous metal
  • Suits all bandsaws which use 64-1/2″ long, 1/2″ wide bandsaw blade

64 1 2 in 5 feet 4 inch 5inch 5inches inches half steel replacement parts bimetal cut hss 1638

  • Blade installation is the first step, make sure teeth is shown outside the guide, and blade strip is clamped tightly inside the guide.
  • Teeth direction should be the same with the direction of wheel rotation, twist the blade from inside to outside if teeth direction is opposite.
  • Running-in is required when blade cuts metal for the first time. It’s important for blade life. During running-in, cutting speed should be 1/3 of normal speed, feed should be 1/4 of normal feed. Usually, after the blade cuts the first several pieces, like 5-10 pieces, adjust cutting speed and feed gradually to normal speed according relative parameters and your metal.
  • Blade tension will be different for differnt wide blades, as time goes on, blade tension will be reduced by the bandsaw and blade stretch, make sure the blade is correct tension, our recommended blade tension is 300N/mm2.
  • Coolant will be useful to cool and lubricate blade and teeth during cutting, better coolant could avoid overheat on the teeth of the blade, and reduce friction between the blade and the metal you cut.
  • Teeth selection is also important, here are our experience:

  1. big variable teeths (like 3/4TPI, 4/6TPI, 5/8TPI) are for cutting ferrous solid rod with big diameter;
  2. big constant teeth (like 6TPI) is for cutting ferrous solid rod with small diameter;
  3. big variable teeth (like 6/10TPI) is for cutting aluminum, copper, brass etc and other non-ferrous metal;
  4. middle variable teeths (like 8/12TPI, 10/14TPI) are for ferrous thick tubing, profile, sheet, plate etc;
  5. small constant teeth (14TPI) is for general purpose;
  6. small variable teeths (like 12/16TPI, 14/18TPI) is for ferrous thin tubing, sheet, plate, profile etc;
  7. small constant teeth (24TPI) is for ferrous thin tubing, plate, sheet etc, don’t cut non-ferrous metal, like aluminum etc.

Reviews

There are no reviews yet.

Be the first to review “Imachinist S64514 Bi-metal Band Saw Blades 64-1/2″ X 1/2″ X 14tpi for Cutting Metal”
SKU: 4PYLOB010B Category:

Related products

  • Sale!

    40 Pack Threaded Insert Nutsert, 1/4″-20 x 15mm Screw in Nut Threaded Wood Inserts, for Wood Furniture(with 1/4″ Allen Wrench)

     Original price was: $37.99.Current price is: $31.66.
    • SIZE: Insert head diameter: 0.445 inch (11.3mm),body diameter: 0.315 inch (8mm),threads diameter: 0.410 inch (10.4mm),1/4-20 threaded insert length: 0.591 inch (15mm); Allen Wrench: 1/4 inch (6mm).
    • Material: High quality carbon steel with high hardness,can keep a long-lasting hold.
    • Application: These furniture screws are suitable for wood furniture,hardwood or solid wood,such as furniture combinations(Threaded inserts are used to drill the right SIZE hole and Install with hex key provided,and screw in nut connector screws).
    • Recommended drill bit for wood: For Soft Wood 3/8 inch (8.5mm/9mm)dirll bit in soft wood,the threads cut will easily go into the wood; For Hard Wood 3/8 inch (10mm),pls drill a hole that close to the outside threads diameter.If the hole is too small,Screwing it may split the wood or insert. If you are not sure the harness of the wood material,pls drill a proper SIZEd hole for test before installing it.
    • Package included: 40 *1/4-20 Threaded Insert Nutsert + 1*1/4 inch(6mm) Allen Wrench.
    Add to cart
  • Sale!

    Tshya 240pcs 2inch Sanding Discs Pad Variety Kit for Drill Grinder Rotary Tools Attachment with 2Pcs 1/8″&1/4″ Shank Backer Plate, Sanding Pads Includes 80-3000 Grit

     Original price was: $64.78.Current price is: $53.98.
    • ? FIRST CHOICE – Premium 2 inch (50mm) aluminum oxide sandpaper with strong hook loop base, 12 kinds of common grits (P80-3000) to meet your various polishing requirements.
    • ? TWO TYPES SHANKS – We have found all the connection methods for your project as far as possible.1/4 inch(6.35mm) Round shank works better with pneumatic tools; 1/4 inch Hex shank more suitable for electric tools.
    • ? THREE WAYS CONNECT ?C The Air-Tool Backer Plate with 1/8″&1/4″ Shank can work with any air or electric drill, die grinder, and other rotary tools for the utmost sanding control. You can even put the pad directly on a pneumatic tool without shank.
    • ? MORE APPLICATIONS – Perfect for home improvement whether it is for woodworking, carving, fabrication, construction or crafting.
    • ? 244 PACK ?C 240Pcs 2 inch Hook and Loop Sanding Discs (P80/120/180/240/320/400/600/800/1000/1500/2000/3000 each 20Pcs)??1Pcs Air-Tool Backer Plate with 1/8″&1/4″ Shank, 1Pcs Sanding Pad with 1/4″Round/Hex Shanks??2Pcs Soft Foam Layer Buffering Pad.
    Add to cart
  • Sale!

    Hard-to-Find Fastener 014973291426 Phillips Flat TwinFast Wood Screws, 4 x 3/4-Inch, 100-Piece

     Original price was: $25.43.Current price is: $21.19.
    • Diameter: No.4
    • Length: 3/4-Inch
    • Material: Steel
    • Finish: Black Phosphate
    • Head Style: Flat (Phillips)
    • Diameter: #4
    • Length: 3/4 inches
    Add to cart
  • Sale!

    Tapcon Concrete Anchors Screws (1/4 inch x 1-1/4 inch) – Slotted Hex Head – 10-Pack

     Original price was: $57.24.Current price is: $47.70.
    • Use: Interior/Exterior
    • Package Quantity: 10
    • Diameter: 1/4 in.
    • Length: 1.25 in.
    Add to cart